NVT210DMTR2G【PDF 12/20 页】IC TEMP SENSOR DGTL 8-WDFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录46

8页 9页 10页 11页 [12页]13页 14页 15页 16页

NVT210

http://onsemi.com

Table 13. LIST OF REGISTERS

Read Address (Hex)

Write Address (Hex)

Name

Power-on Default

Not Applicable

Address Pointer

Undefined

Not Applicable

Local Temperature Value

0000 0000 (0x00)

Not Applicable

External Temperature Value High Byte

0000 0000 (0x00)

Not Applicable

Status

Undefined

Configuration

0000 0000 (0x00)

Conversion Rate

0000 1000 (0x08)

Local Temperature High Limit

0101 0101 (0x55) (85癈)

Local Temperature Low Limit

0000 0000 (0x00) (0癈)

External Temperature High Limit High Byte

0101 0101 (0x55) (85癈)

External Temperature Low Limit High Byte

0000 0000 (0x00) (0癈)

Not Applicable

0F (Note 1)

One-shot

Not Applicable

External Temperature Value Low Byte

0000 0000

External Temperature Offset High Byte

0000 0000

External Temperature Offset Low Byte

0000 0000

External Temperature High Limit Low Byte

0000 0000

External Temperature Low Limit Low Byte

0000 0000

External THERM

Limit

0101 0101 (0x55) (85癈) (Note 2)

Local THERM

Limit

0101 0101 (0x55) (85癈)

THERM

Hysteresis

0000 1010 (0x0A) (10癈)

Consecutive ALERT

0000 0001 (0x01)

Not Applicable

Manufacturer ID

0100 0001 (0x41)

1. Writing to Address 0x0F causes the NVT210 to perform a single measurement. It is not a data register, and it does not matter what data is

written to it.

2. THERM

limit for MSOP8 package = 85癈, THERM

limit for WDFN8 package = 108癈.

Serial Bus Interface

Control of the NVT210 is carried out via the serial bus.

The NVT210 is connected to this bus as a slave device, under

the control of a master device.

The NVT210 has an SMBus/I

C timeout feature. When

this is enabled, the SMBus/I

C times out after typically

25 ms of no activity. However, this feature is not enabled by

default. Bit 7 of the consecutive alert register

(Address = 0x22) should be set to enable it.

Addressing the Device

In general, every SMBus/I

C device has a 7-bit device

address, except for some devices that have extended 10-bit

addresses. When the master device sends a device address

over the bus, the slave device with that address responds.

The NVT210 is available with one device address, 0x4C

(1001 100b). An NVT210D is also available.

The NVT210D has an SMBus/I

C address of 0x4D

(1001 101b). This is to allow two NVT210 devices on the

same bus, or if the default address conflicts with an existing

device on the SMBus/I

C. The serial bus protocol operates

as follows:

1. The master initiates a data transfer by establishing

a start condition, defined as a high-to-low

transition on SDATA, the serial data line, while

SCLK, the serial clock line, remains high. This

indicates that an address/data stream follows. All

slave peripherals connected to the serial bus

respond to the start condition and shift in the next

eight bits, consisting of a 7-bit address (MSB first)

plus an R/W

bit, which determines the direction of

the data transfer, that is, whether data is written to,

or read from, the slave device. The peripheral

whose address corresponds to the transmitted

address responds by pulling the data line low

during the low period before the ninth clock pulse,

known as the acknowledge bit. All other devices

on the bus remain idle while the selected device

waits for data to be read from or written to it. If the

R/W

bit is a 0, the master writes to the slave

device. If the R/W

bit is a 1, the master reads from

the slave device.

2. Data is sent over the serial bus in a sequence of

nine clock pulses, eight bits of data followed by an

acknowledge bit from the slave device. Transitions

on the data line must occur during the low period

of the clock signal and remain stable during the

high period, since a low-to-high transition when

the clock is high can be interpreted as a stop

signal. The number of data bytes that can be

transmitted over the serial bus in a single read or

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式